The user is granted access to the VPN or endpoint server and establishes an encrypted tunnel to the internal network. The clients will be on windows mac and iphone/ipad.From Administrative Tools select Network Policy Server Right click on Radius Clients and Select New Add a name, the ip address of your remote access server (RAS, VPN, etc) and create a shared secret.This document provides a sample configuration for the Protected Extensible Authentication Protocol (PEAP) with Microsoft Challenge Handshake Authentication Protocol (MS-CHAP) version 2 authentication in a Cisco Unified Wireless network with the Microsoft Network Policy Server (NPS) as the RADIUS server.If the authentication is successful, the NPS server sends a RADIUS Access-Accept message to the VPN or endpoint server. I would like all authentication to be done with username and password not certificate. I have VPN working with pfsense pptp so far in my test environment. I have been trying to setup Server 2008 R2 Network Policy Server to authenticate my VPN and Wifi.Configure your VPN server to use RADIUS authentication. Configuring MFA for VPN Prerequisites: Professional Edition license of ADSelfService Plus. Authentication and RADIUS accounting are configured to use the NPS server.The user is granted access to the VPN server and establishes an encrypted tunnel to the internal network.Install the Microsoft Windows Server 2008 operating system on each of the servers in the test lab. Knowledge of Cisco controller installationEnsure that these requirements have been met before you attempt this configuration: Important Network Policy Server (NPS) does not support the use of the Extended ASCII characters within passwords. Knowledge of basic Windows 2008 installationFor more information on deploying server certificates to NPS and Remote Access servers, see Deploy Server Certificates for 802.1X Wired and Wireless Deployments.
Nps For Vpn Access Security 2008 Certificate Mac And IphoneWindows 2008 Enterprise Server with NPS, Certificate Authority (CA), dynamic host control protocol (DHCP), and Domain Name System (DNS) services installedThe information in this document was created from the devices in a specific lab environment. Cisco Aironet 3602 Access Point (AP) with Lightweight Access Point Protocol (LWAPP) Cisco 5508 Wireless Controller that runs firmware Version 7.4 The Cisco Technical Assistance Center (TAC) does not support Microsoft Windows server configuration.Microsoft Windows 2008 installation and configuration guides can be found on Microsoft Tech Net.The information in this document is based on these software and hardware versions: If you have trouble with the configuration, contact Microsoft for help. The Microsoft Windows server configuration presented in this document has been tested in the lab and found to work as expected. After authentication is successfully completed between the wireless client and NPS, the TLS session is negotiated between the client and NPS. After the IEEE 802.11-based association is successfully established between the client and the access point, the TLS session is negotiated with the AP. An IEEE 802.11-based association provides an open system or shared key authentication before a secure association is created between the client and the access point. The PEAP authentication process consists of two main phases.The wireless client associates with the AP. PEAP does not specify an authentication method, but provides additional security for other Extensible Authentication Protocols (EAPs), such as EAP-MS-CHAP v2, that can operate through the TLS-encrypted channel provided by PEAP. If your network is live, make sure that you understand the potential impact of any command.Refer to the Cisco Technical Tips Conventions for more information on document conventions.PEAP uses Transport Level Security (TLS) to create an encrypted channel between an authenticating PEAP client, such as a wireless laptop, and a PEAP authenticator, such as Microsoft NPS or any RADIUS server. The client responds with an identity response message: EAP-Response/Identity. The NPS sends an identity request message to the client: EAP-Request/Identity. The Wireless LAN Controller (WLC) and the LAP cannot decrypt these messages because it is not the TLS end point.The RADIUS message sequence for a successful authentication attempt (where the user has supplied valid password-based credentials with PEAP-MS-CHAP v2) is: The LAP and the controller only forward messages between the wireless client and RADIUS server. The NPS authenticates the wireless client with EAP-MS-CHAP v2. ![]() Active Directory ? to maintain the user databaseThe server connects to the wired network through a Layer 2 switch as shown. The WLC and the registered LAP also connect to the network through the Layer 2 switch.The wireless clients use Wi-Fi Protected Access 2 (WPA2) - PEAP-MS-CHAP v2 authentication to connect to the wireless network.The objective of this example is to configure the Microsoft 2008 server, Wireless LAN Controller, and Light Weight AP to authenticate the wireless clients with PEAP-MS-CHAP v2 authentication. NPS ? to authenticate the wireless users Domain controller for the domain wireless.com If VLANs are deployed for client isolation, the VLAN attributes are included in this message.In this section, you are presented with the information to configure PEAP-MS-CHAP v2.Note: Use the Command Lookup Tool ( registered customers only) to obtain more information on the commands used in this section.This configuration uses this network setup:In this setup, a Microsoft Windows 2008 server performs these roles: install and configure the server as a CA server. Configure the server as a domain controller. Configure the WLC and the Light Weight APs.Configure the Microsoft Windows 2008 ServerIn this example, a complete configuration of the Microsoft Windows 2008 server includes these steps: Configure the Microsoft Windows 2008 Server. Click Install to begin the installation process. Review the Introduction to Active Directory Domain Services, and click Next. Select the service Active Directory Domain Services, and click Next. Enter the full DNS name for the new domain (wireless.com in this example), and click Next. Click Create a new domain in a new forest > Next in order to create a new domain. Review the information on Operating System Compatbilty, and click Next. Click Next to run the Active Directory Domain Services Installation Wizard. Click Yes for the installation wizard to create a new zone in DNS for the domain. Ensure DNS server is selected, and click Next. Select the domain functional level for your domain, and click Next. Review the Introduction to DHCP Server, and click Next. Select the service DHCP Server, and click Next. Complete these steps in order to install and configure DHCP services: Restart the server for the changes to take effect.Install and Configure DHCP Services on the Microsoft Windows 2008 ServerThe DHCP service on the Microsoft 2008 server is used to provide IP addresses to the wireless clients. Review your selections, and click Next. Enter the Administrator Password, and click Next. Objective physics medical dc pandey pdfConfigure IPv6 DNS settings if DHCPv6 was enabled in the preceding step. Enable or disable DHCPv6 support on the server, and click Next. Click Add to use the wizard to create a DHCP Scope or click Next to create a DHCP scope later. Configure WINS if the network supports WINS. Configure the default DNS settings the DHCP server should provide to clients, and click Next. Click Next to configure the new scope via the New Scope Wizard. Expand the DHCP server (win-mvz9z2umms.wireless.com in this example), right-click IPv4, and choose New Scope. Click Start > Administrative Tools > DHCP to configure DHCP service. Review the configuration on the confirmation page, and click Install to complete the install.
0 Comments
Leave a Reply. |
AuthorJeanabec ArchivesCategories |